Free shipping* Performance Guaranteed online support
CALL US 201.935.2910
KING XPG SERIES ROD BEARINGS 52MM JOURNAL | SUBARU EJ-SERIES (CR4125XPG)

KING XPG SERIES ROD BEARINGS 52MM JOURNAL | SUBARU EJ-SERIES (CR4125XPG)

IAG Performance Stage 1 2.5L Subaru Short Block For WRX, STI, Legacy GT & Forester XT

Features
  • Manley 99.5mm Platinum Series Pistons, Ringset, Tool Steel Pins and Clips (w/ Coated Skirts and Offset Wrist Pin)
  • New FHI Subaru Case Halves at 99.5mm stock bore 
  • New FHI Subaru Early STI (Stronger Style) Connecting Rods
  • New FHI Subaru Nitride Treated 2017+ STI Crankshaft
  • ACL or King Rod Bearings
  • ACL or King Main Bearings
  • New FHI Main Case Bolts
  • IAG Spec Blueprint Sheet
  • Power Output Rating: 475BHP
$2,899.99
In stock
SKU
Iag-2.5-1

IAG Stage 1 Short Block


The IAG Stage 1 Short Block is perfect for lightly modified EJ25 Subaru's that need a basic and reliable performance short block. Subaru turbo engines are commonly known for piston ring land failures and if gone unchecked lead to rod knock and total engine failure due to oil starvation from blow by. IAG's Stage 1 Short Block includes upgraded forged pistons along with performance main and rod bearings that replace the OEM components that are prone to common failure on Stage 2 and up vehicles. Each IAG Stage 1 Short Block starts with new Subaru 2.5L 99.5mm bore EJ25 engine case halves as standard. The short block is measured and assembled using a new 2017+ Nitride Treated Subaru 2.5L STI crankshaft that is matched to ACL or King main bearings. Early style OEM STI rods are utilized along with ACL or King rod bearings. The case halves are sealed with new OEM case bolts and sealant. Finally, Manley 99.5mm Platinum Series Forged Pistons are spec'd and installed finishing off the short block. 

The IAG Stage 1 Short Block has a power output rating of 475BHP. 

Stage 1 Short Block Includes:

  • Case Halves - Brand new Subaru OEM case halves 99.5mm Stock Bore
  • Pistons - Manley 99.5mm Platinum Forged Pistons, Ringset, Tool Steel Pins, Clips, (Coated Skirts and Offset Wrist Pin)
  • Connecting Rods - Early OEM (Stronger Style) STI rods
  • Rod / Main Bearings - ACL or King Bearings
  • Crankshaft - Standard New Subaru Nitride Treated 2017+ STI Crankshaft
  • Case / Main Bolts - Standard FHI Subaru case bolts


Additional Options Available:

  • Hardware / Seals - OEM cover and seal kit - $105.99


*All IAG short blocks are balanced and blueprinted.

Compression Ratio: 8.5:1 on D Cylinder Heads (EJ255) 
Compression Ratio: 8.2:1 on B, V and W EJ257 Heads with standard thickness gasket.


Hardware / Seal Option:

Subaru EJ25 Seal Kit


Not planning on reusing your original short block service plugs and covers? IAG offers a simple comprehensive cover and seal kit that includes (1) Rear main seal, (3) OEM wrist pin plugs, (3) OEM wrist pin plug washers, (1) OEM separator cover, (6) OEM separator cover bolts, (1) OEM wrist pin service cover, (1) OEM wrist pin service cover O-ring and (2) OEM wrist pin service cover screws. *If you are reusing your original wrist pin service plugs and covers always replace the (3) OEM wrist pin plug washers and (1) wrist pin service cover O-ring before installing a short block to avoid potential leaks. *Never reuse a rear main seal on a new short block. 

Write Your Own Review
You're reviewing:IAG Performance Stage 1 2.5L Subaru Short Block For WRX, STI, Legacy GT & Forester XT